|
LAVAMAT 73742 VI
WASHING MACHINE
USER MANUAL
EN
Contents
3
CONTENTS
4 Safety information
6 Technical data
6 Product description
8 Control panel
10 First use
10 Personalization
11 Daily use
16 Washing programmes
20 Consumption values
20 Helpful hints and tips
22 Care and cleaning
27 What to do if…
31 Installation
36 Electrical connection
37 Building-in
38 Environment concerns
The following symbols are used in this user
manual:
Important information concerning your
personal safety and information on how to
avoid damaging the appliance.
General information and tips
Environmental information
Subject to change without notice
4
Safety information
SAFETY INFORMATION
Read carefully & keep for future reference.
• The safety of Your appliance complies with the industry standards and with legal re-
quirements on the safety of appliances. However, as manufacturers, we feel it is our duty
to provide the following safety notes.
• It is most important that this instruction book should be retained with the appliance for
future reference. Should the appliance be sold or transferred to another owner, or should
you move house and leave the appliance, always ensure that the book is supplied with
the appliance in order that the new owner can get to know the functioning of the appli-
ance and the relevant warnings.
• You MUST read them carefully before installing or using the appliance.
• Before first starting up, check the appliance for any damage incurred during transport.
Never connect up a damaged appliance . If parts are damaged, contact your supplier.
• If the appliance is delivered in the winter months when there are minus temperatures.
Store it at room temperature for 24 hours before using for the first time.
General safety
• It is dangerous to alter the specifications or attempt to modify this product in any way.
• During high temperature wash programmes the door glass may get hot. Do not touch it!
• Make sure that small pets and children do not climb into the drum. To avoid this, please
check into the drum before using.
• Any objects such as coins, safety pins, nails, screws, stones or any other hard, sharp ma-
terial can cause extensive damage and must not be placed into the machine.
• Only use the advised quantities of fabric softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the manufacturer’s recommendations of quantities.
• Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case
as it is possible for such items to slip down between the tub and the inner drum.
• Do not use your washing machine to wash articles with whalebones, material without
hems or torn material.
• Always unplug the appliance and turn off the water supply after use, cleaning and main-
tenance.
• Under no circumstances should you attempt to repair the machine yourself. Repairs car-
ried out by inexperienced people may cause injury or serious malfunctioning. Contact
your local Service Centre. Always insist on genuine spare parts.
Installation
• This appliance is heavy. Care should be taken when moving it.
• When unpacking the appliance, check that it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packing and transit bolts must be removed before use. Serious damage can occur to
the product and to property if this is not adhered to. See relevant section in the user
manual.
Safety information
5
• After having installed the appliance, check that it is not standing on the inlet and drain
hose and the worktop is not pressing the electrical supply cable against the wall.
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air
to circulate freely under the appliance.
• Always be sure, that there is no water leakage from hoses and their connections after the
installation.
• If the appliance is installed in a location subject to frost, please read the “dangers of
freezing” chapter.
• Any plumbing work required to install this appliance should be carried out by a qualified
plumber or competent person.
• Any electrical work required to install this appliance should be carried out by a qualified
electrician or competent person.
Use
• This appliance is designed for domestic use. It must not be used for purposes other than
those for which it was designed.
• Only wash and dry fabrics which are designed to be machine washed or dried. Follow the
instructions on each garment label
• Do not overload the appliance. See the Washing Programme Table.
• Before washing, ensure that all pockets are empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass
before washing. Underwired bras must NOT be machine washed.
• Garments which have been in contact with volatile petroleum products should not be
machine washed. If volatile cleaning fluids are used, care should be taken to ensure that
the fluid is removed from the garment before placing in the machine.
• As some duvets and eiderdowns should be washed/dried in large commercial machines
because of their bulk, please check with the manufacturer of the item before washing in
a domestic machine.
• The users should always check that they have not left their gas lighters (disposable or
otherwise) in their clothing.
• Never tumble dry items that have had contact with chemicals such as dry cleaning fluid.
These are of a volatile nature and could cause an explosion. Only tumble dry items which
have been washed in water or require airing.
• Plastic detergent dispensers should not remain in the drum during the drying cycle, as
the plastic used is not designed to withstand the heat. If you wish to wash-through-to-
dry you should use the conventional detergent dispenser drawer.
• Never pull the power supply cable to remove the plug from the socket; always take hold
of the plug itself.
• Never use your new appliance if the power supply cable, the control panel, the working
surface or the base are damaged so that the inside of the appliance is accessible.
Child Safety
• This appliance is not intended for use by person (including children) with reduced physi-
cal sensory or mental capabilities or lack of experience and knowledge unless they have
6
Technical data
been given supervision or instruction concerning use of the appliance by a person re-
sponsible for their safety.
• The packaging components (e.g. plastic film, polystyrene) can be dangerous to children -
danger of suffocation! Keep them out of children's reach.
• Keep all detergents in a safe place out of children’s reach.
• Make sure that children or pets do not climb
into the drum. To prevent children or pets
becoming trapped inside the drum the ma-
chine incorporates a special feature. To acti-
vate this device, rotate the button (without
pressing it) inside the door clockwise until
the groove is horizontal. If necessary use a
coin. To disable this device and restore the
possibility of closing the door, rotate the
button anticlockwise until the groove is ver-
tical.
TECHNICAL DATA
Dimensions
Width
Height
Depth
60 cm
82 cm
54 cm
Electrical connection
Information on the electrical connection is given on the rating
Voltage - Overall power - Fuse plate, on the inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
6 kg
Maximum
1400 rpm
PRODUCT DESCRIPTION
Your new appliance meets all modern requirements for effective treatment of laundry with
low water, energy and detergent consumption.
The NEW JET system allows total use of detergent and reduces water consumption so sav-
ing energy.
Product description
7
2
1
3
4
5
6
1 Detergent dispenser drawer
2 Control panel
3 Door opening handle
4 Rating plate
5 Drain pump
6 Adjustable feet
Detergent dispenser drawer
Compartment for prewash phase or stain re-
mover.
The prewash detergent is added at the beginning
of the wash programme.
The stain remover is added during the STAIN-Ac-
tion phase in the main wash.
Compartment for powder or liquid detergent
used for main wash.
Compartment for liquid additives (fabric soft-
ener, starch).
Follow the product manufacturer’s recommendations on quantities to use and do not ex-
ceed the «MAX» mark in the detergent dispenser drawer. Any fabric softener or starching
additives must be poured into the compartment before starting the wash programme.
8
Control panel
CONTROL PANEL
Below is a picture of the control panel. It shows the programme selector dial as well as the
buttons and the display. These are presented by relevant numbers on the following pages.
9
1
2
3
4
5
6
7
8
1 Programme selector dial
2 TEMPERATURE button
3 SPIN reduction button
4 OPTION button
5 OK button
6 TIME SAVING button
7 START/PAUSE button
8 DELAY START button
9 Display
Table of Symbols
Cottons/Lin-
Jeans
Synthetics
en
Easy iron
Drain
Delicates
Long spin
Silk
Delicate rinses
Delicate spin
Hand wash
Wool plus
Refresh
Temperature
Time saving
Spin reduction
Start/Pause
Options
Delay start
9
Display
9.1
9.2
9.3
9.9
9.4
9.5
9.6 9.7 9.8
9.1 - Temperature indicator and COLD
9.2 - Spin Speed indicator, RINSE HOLD
9.3 - Programme progress display: PREWASH
DRAIN , OVERDOSAGE
symbol
, NIGHT CYCLE
- symbols
, RINSE
, MAIN WASH
, SPIN
,
• The programme progress display shows the washing phases of the selected programme.
• During a washing cycle, a black line blinks under the washing phase symbol of the run-
ning programme. At the end of each washing phase, the line under the corresponding
symbol becomes fixed.
If the OVERDOSAGE symbol lights up at the end of the programme, it indicates that too
much detergent has been used.
9.4 - Options: PREWASH
9.5 - DOOR - symbol (Door locked)
• This symbol indicates if the door can be opened:
, STAIN
, SENSITIVE
, EXTRA RINSE
– the symbol is on: the door cannot be opened. The appliance is performing a washing
programme.
– the symbol is off: the door can be opened. The washing programme is finished.
9.6 - TIME SAVING
- option symbol
9.7 - The display shows the following information:
• Duration of the selected programme
– After selecting a programme, the duration is displayed in hours and minutes (for ex-
ample
. The duration is calculated automatically on the basis of the maximum
recommended load for each type of fabric.
– After the programme has started, the time remaining is updated every minute.
• Delay start
– The selected delay (20 hours max) set by means of the relevant button appears on the
display for about 3 seconds (for example
selected programme is displayed.
), then the duration of the previously
– The DELAY START symbol will appear on the display.
– The delay time value decreases by one unit every hour and then, when remains 1 hour,
the time decreases every minute.
• Incorrect option selection
10
First use
– If an option which is not compatible with the set wash programme is selected, the
message Err is displayed for about 2 seconds and the yellow light of button 7 starts
blinking.
• Alarm codes
– In the event of operating problems, some alarm codes can be displayed, for example
(see chapter «What to do if...»).
• End of the programme
– When the programme has finished a blinking zero is displayed, the DOOR symbol
disappears and the door can be opened.
9.8 - DELAY START
- symbol
9.9 - CHILD SAFETY LOCK - symbol
FIRST USE
• Ensure that the electrical and water connections comply with the installation instruc-
tions.
• Remove the polystyrene block and any material from the drum.
• Before the first wash, run a cotton cycle at the highest temperature without any laundry
in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a
measure of detergent into the main wash compartment and start the machine.
PERSONALIZATION
Acoustic signals
The machine is provided with an acoustic device, which sounds in the following cases:
• at the end of the cycle
• in the event of operating problems.
By pressing the 3 and 4 buttons simultaneously for about 6 seconds, the acoustic signal is
deactivated (except for the events of operating problems). By pressing these two buttons
again, the acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appliance unattended and not to worry that children
might be injured by or cause damage to the appliance.
This function remains able also when the washing machine is not working.
To enable (or disable) this option press simultaneously for about 6 seconds buttons 4 and 5
until the Child Lock symbol appears on (or disappears from) the display.
There are two different ways to set this option:
• Before pressing button 7: it will be impossible to start the machine.
• after pressing button 7: it will be impossible to change any other programme or option.
Daily use
11
DAILY USE
Load the laundry
1. Open the door by carefully pulling the
door handle outwards. Place the laundry
in the drum, one item at a time, shaking
them out as much as possible.
2. Close firmly the door. You must hear a
click during closing.
WARNING!
Do not embed the laundry between the door
and the rubber joint.
Measure out the detergent and the fabric softener
Your new appliance was designed to reduce water, energy and detergent consumption.
1. Pull out the dispenser drawer until it
stops. Measure out the amount of deter-
gent required, pour it into the main wash
compartment
and, if you wish to carry
out the prewash phase or to perform the
stain function, pour the detergent or the
stain remover into the compartment
marked
.
2. If required, pour fabric softener into the
compartment marked (the amount
used must not exceed the MAX mark in
the drawer). Close the drawer gently.
12
Daily use
Select the required programme by means of programme selector dial (1)
You can choose the right programme for any type of laundry following the descriptions on
the washing programme tables (see «Washing Programmes»).
Turn the programme selector dial to the required programme. The programme selector de-
termines the type of washing cycle (e.g. water level, drum movement, number of rinses) and
the washing temperature according to the type of laundry.
The pilot light of button 7 starts blinking and the display shows the duration of the selected
programme.
The selector dial can be turned either clockwise or anticlockwise. Position
gramme/ Switching OFF of the machine.
to Reset pro-
At the end of the programme the selector dial must be turned to position
switch the machine off.
, to
If you turn the programme selector dial to another programme when the machine is work-
ing, the yellow pilot light of button 7 will blink 3 times and the message Err is displayed on
the display to indicate a wrong selection. The machine will not perform the new selected
programme.
Select the desired TEMPERATURE (Button 2)
When selecting a programme, the appliance automatically proposes the default tempera-
ture provided for that programme.
Press this button repeatedly to increase or decrease the temperature, if you want your
laundry to be washed at a temperature different from the one proposed by the washing
machine.
The symbol of cold wash corresponds to - - (
) .
For the maximum and the minimum available wash water temperature, see «Washing pro-
grammes».
Select the spin speed, NIGHT CYCLE or RINSE HOLD option (button 3)
When the required programme has been selected, your appliance automatically proposes
the maximum spin speed provided for that programme.
Press this button repeatedly to change the spin speed, if you want your laundry to be spun
at a speed different from the one proposed by the washing machine.
RINSE HOLD: by selecting this option the water of the last rinse is not emptied out to pre-
vent the fabrics from creasing. At the end of the programme, and RINSE HOLD symbol
appear on the display, DOOR symbol (door locked) remains lit, the pilot light of button 7
goes off and the door is blocked to indicate that the water must be emptied out.
NIGHT CYCLE: by selecting this option, the machine will not drain the water of the last
rinse, so as not to wrinkle the laundry. As all spinning phases are suppressed, this washing
cycle is very noiseless and it can be selected at night or in times with a more economical
power rate. In some programmes the rinses will be performed with more water. At the end
of the programme, and RINSE HOLD symbol appear on the display, the DOOR symbol re-
mains lit, the pilot light of button 7 goes off and the door is blocked to indicate that the
water must be emptied out.
Daily use
To empty out the water, please read chapter «At the end of the programme».
13
Programme option buttons
Depending on the programme, different functions can be combined.
WARNING!
Not all the options are compatible among themselves. The symbols of the incompatible op-
tions disappear.
Anyway, if an option, which is not compatible with the set washing programme or any oth-
er option, is selected, the Err message is displayed for few seconds and the yellow pilot of
button 7 light starts blinking.
You must select the options after you have selected the programme but before pressing the
button 7. Press the button 4: all the option symbols appear on the display.
To scroll all the available options, press the button 4. The corresponding symbol appears on
the display and starts blinking.
Press the button 5 to activate and confirm your choice. A black dash appears under the
selected symbol to indicate that this option has been set. Press the same button to deacti-
vate the option.
After selecting the options, wait about few seconds until the display gets back to the de-
fault status. The selected options appear on the display.
For the compatibility among the options and the washing programmes see chapter «Wash-
ing Programmes».
PREWASH option
Select this option if you wish your laundry to be prewashed at 30°C before the main wash.
The Prewash ends with a short spin in programmes for cotton and synthetic fabrics, where-
as in the programmes for delicate fabrics the water is only drained.
The relevant symbol will appear on the display.
This option is recommended for heavily soiled laundry.
STAIN option
Select this option to treat heavily soiled or stained laundry with stain remover (extended
main wash with time optimized stain action phase). The relevant symbol will appear on the
display.
This option is not available with a temperature lower than 40°C.
If you wish to perform a programme with the stain option, pour stain remover into stain
compartment
.
The PREWASH option and the STAIN option cannot be selected together.
SENSITIVE option
By selecting this option the washing intensity will be reduced. The machine adds one rinse
in the programmes for cottons and synthetics. The relevant symbol will appear on the dis-
play.
This option cannot be selected together with Extra Rinse option.
This option is recommended for non fast coloured items and for frequently washed items.
14
Daily use
EXTRA RINSE option (additional rinse)
This appliance is designed for saving water. However, for people with a very delicate skin
(allergic to detergents) it may be necessary to rinse the laundry using an extra quantity of
water (extra rinse). The relevant symbol will appear on the display and this option is active
for selected washing programme.
If you wish to activate this option permanently press simultaneously buttons 2 and 3 for
some seconds: the relevant symbol appears on the display. If you wish to cancel it press the
same buttons until the symbol disappears.
Select the TIME SAVING option (button 6)
This option allows you to modify the washing time, automatically proposed by the appli-
ance.
By pressing this button you can select the following options:
DAILY: by pressing button 6 once, the corresponding symbol appears on the display and the
washing duration will be reduced to wash daily soiled laundry. Reduced washing time is
presented on the display.
SUPER QUICK: by pressing button 6 twice, the corresponding symbol remains lit on the dis-
play and the washing duration will be reduced to wash lightly soiled laundry or items that
have been used or worn for a short time. Reduced washing time is presented on the display.
Select the START/PAUSE (button 7)
To start the selected programme, press the button 7, the corresponding red pilot light stops
blinking.
The DOOR symbol appears on the display to indicate that the appliance has started operat-
ing and the door is locked.
To interrupt a programme which is running, press the button 7: the corresponding red pilot
light starts blinking.
To restart the programme from the point at which it was interrupted, press the button 7
again. If you have chosen a delayed start the machine will begin the countdown.
If an incorrect option is selected, the yellow pilot light of the button 7 blinks 3 times and
the message Err is displayed for a few seconds.
Select the DELAY START (button 8)
Before you start the programme, if you wish to delay the start, press the button repeated-
ly, to select the desired delay.
The corresponding symbol will appear on the display. The wash programme can be delayed
from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours
by means of this button.
The selected delay time value will appear on the display for about 3 seconds, then the dura-
tion of the programme will appear again.
You must select this option after you have set the programme and before you press the
button 7.
You can modify or cancel the delay time at any moment, before you press the button 7.
The door will be locked throughout the delay time. If you wish to add laundry in the ma-
chine during the delay time, press the button 7 to set the machine to pause. When the Door
symbol disappears, the door can be opened. Add the laundry, close the door and press the
button 7 again.
Daily use
15
Selecting the delayed start.
• Select the programme and the required options.
• Select the delay start.
• Press button 7: the appliance starts its hourly countdown. The programme will start after
the selected delay has expired.
Cancelling the delayed start
• Set the washing machine to PAUSE by pressing the button 7;
• Press button 8until the symbol ’ is displayed;
• Press the button 7 again to start the programme.
The selected delay can be changed only after selecting the washing programme again.
The Delay Start can not be selected with Drain programme.
Altering an option or a running programme
It is possible to change some options before the programme carries them out. Before you
make any change, you must pause the washing machine by pressing the button 7.
Changing a running programme is possible only by resetting it. Turn the programme selec-
tor dial to
and then to the new programme position. Start the new programme by
pressing the 7 button again. The washing water in the tub will not emptied out.
Interrupting a programme
Press the button 7 to interrupt a programme which is running, the corresponding light
starts blinking. Press the button again to restart the programme.
Cancelling a programme
Turn the selector dial to
new programme.
to cancel a programme which is running. Now you can select a
Opening the door after the programme has started
First set the machine to pause by pressing the button 7.
• If the DOOR symbol disappears, the door can be opened;
• If the DOOR symbol doesn’t go off, it means that the machine is already heating, that the
water level is above the bottom edge of the door. In this case the door cannot be
opened;
• If you cannot open the door but you need to open it, you have to switch the machine off
by turning the selector dial to
attention to the water level and temperature!);
After closing the door, it is necessary to select the programme again and to press button 7.
. After some minutes the door can be opened (pay
At the end of the programme
The machine stops automatically, the pilot light of button 7 pilot light goes off, a blinking
appears on the display and the acoustic signal sounds for some minutes.
If you have chosen a programme or an option that ends with water in the tub, follow the
below instruction to empty the water out:
16
•
turn the programme selector dial to
• select the DRAINING or SPINNING programme
• reduce the spin speed if needed, by means of the relevant button
• press the button 7
• when the programme has finished the display shows a blinking . On the display the
DOOR symbol disappears and the door can be opened.
Turn the programme selector dial to
to switch the machine off. Remove the laundry
from the drum and carefully check that the drum is empty.
If you do not intend to carry out another wash, close the water tap. Leave the door open to
prevent the formation of mildew and unpleasant smells.
Stand by : once the programme has finished after a few minutes the energy saving system
will be enabled. The brightness of the display is reduced. By pressing any button the appli-
ance will come out of the energy saving status.
WASHING PROGRAMMES
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
COTTONS/LINEN
SPIN reduction /
95°- Cold
NIGHT CYCLE / RINSE
HOLD, PREWASH1),
STAIN, SENSITIVE, EX-
TRA RINSE, TIME SAV-
Main wash - Rinses - Long spin
Maximum spin speed 1400 rpm
Max. load 6 kg - Reduced load 3 kg
For white and coloured cotton (normally soiled
items).
ING2)
40- 60 MIX
SPIN reduction /
40°
NIGHT CYCLE / RINSE
HOLD, PREWASH1)
STAIN , SENSITIVE,
EXTRA RINSE
,
Main wash - Rinses - Long spin
Maximum spin speed 1400 rpm
Max. load 6 kg
White and coloured cotton This programme can be
used for laundry, which should be washed at 40°C or
60°C separately. The maximum load capacity can be
put into the drum in order to save energy and water.
The same good washing result will be obtained as for
normal programme at 60°C.
Washing programmes
17
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
JEANS
SPIN reduction /
NIGHT CYCLE / RINSE
HOLD, PREWASH1)
60° - Cold
Main wash - Rinses - Long spin
Maximum spin speed 1200 rpm
Max. load 3 kg
With this programme it is possible to wash items like
pants, shirts or jackets in Jeans and also jersey realiz-
ed with hi-tech materials. (The Extra Rinse option will
be activated automatically).
SYNTHETICS
SPIN reduction /
60°- Cold
NIGHT CYCLE / RINSE
HOLD, PREWASH1),
STAIN, SENSITIVE, EX-
TRA RINSE, TIME SAV-
Main wash - Rinses - Short spin
Maximum spin speed 1200 rpm
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured
garments, non-shrink shirts, blouses.
ING 2)
EASY IRON
SPIN reduction /
RINSE HOLD, PRE-
WASH1), EXTRA RINSE
60°- Cold
Main wash - Rinses - Short spin
Maximum spin speed 1200 rpm
Max. load 1,5 kg
Synthetic fabrics to be gentle washed and spun.
Selecting this programme the laundry is gently wash-
ed and spun to avoid any creasing. In this way ironing
is easier. Furthermore the machine will perform addi-
tional rinses.
DELICATES
SPIN reduction /
NIGHT CYCLE / RINSE
HOLD , PREWASH1)
STAIN, EXTRA RINSE,
TIME SAVING2)
40°- Cold
Main wash - Rinses - Short spin
Maximum spin speed 1200 rpm
Max. load kg 3 - Reduced. load kg 1,5
Delicate fabrics: acrylics, viscose, polyester.
,
DELICATE RINSES
SPIN reduction /
NIGHT CYCLE / RINSE
HOLD , EXTRA RINSE
Rinses - Short spin
Maximum spin speed 1200 rpm
Max. load 3 kg
With this programme it is possible to rinse and spin
cotton garments which have been washed by hand.
The machine performs some rinses, followed by a fi-
nal spin.
18
Washing programmes
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
DRAIN
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in pro-
grammes with the Rinse Hold or Night Cycle option
selected.
SPIN
Drain and long spin
SPIN reduction
Maximum spin speed 1400 rpm
Max. load 6 kg
Separate spin for hand washed cotton garments and
after programmes with the Rinse Hold or Night Cycle
option selected. Before selecting this programme the
selector dial must be turned to
. You can choose
the spin speed by pressing the relevant button to
adapt it to the fabrics to be spun.
DELICATE SPIN
Drain and short spin
SPIN reduction
Maximum spin speed 1200 rpm
Max. load 3 kg
Separate spin for hand washed cotton garments and
after programmes with the Rinse Hold or Night Cycle
option selected. Before selecting this programme the
selector dial must be turned to
. You can choose
the spin speed by pressing the relevant button to
adapt it to the fabrics to be spun.
WOOL PLUS/HAND WASH
SPIN reduction /
NIGHT CYCLE / RINSE
HOLD
40° - Cold
Main wash - Rinses - Short spin
Maximum spin speed 1000 rpm
Max. load 2 kg
Washing programme for machine washable wool as
well as for hand washable woollens and delicate fab-
rics. Note : A single or bulky item may cause imbal-
ance. If the appliance doesn’t perform the final spin
phase, add more items, redistribute the load manually
and then select the spinning programme.
Washing programmes
19
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Detergent
Compartment
Options
SILK/ HAND WASH
SPIN reduction /
NIGHT CYCLE / RINSE
HOLD
30°
Prewash - Main wash - Rinses - Short spin
Maximum spin speed 1200 rpm
Max. load 1 kg
Special programme is suitable for washing heavily
soiled sport items. The machine will add automatical-
ly a prewash phase before the main wash to elimi-
nate mud stains. We recommend you NOT to put the
detergent into the
drawer.
compartment of the detergent
FRESH UP
30°
SPIN reduction
Main wash - Rinses - Short spin
Maximum spin speed 1200 rpm
Max. load 3 kg
This programme may be used for a quick washing of
sport items or cotton and synthetic items , lightly
soiled or worn once.
ECO
SPIN reduction /
60°
NIGHT CYCLE / RINSE
HOLD, PREWASH1),
STAIN, SENSITIVE, EX-
TRA RINSE
Main wash - Rinses - Long spin
Maximum spin speed 1400 rpm
Max. load 6 kg
White and fast coloured cotton.
This programme can be selected for slightly or nor-
mally soiled cotton items. The temperature will de-
crease and the washing time will be extended. This al-
lows to obtain a good washing efficiency so saving
energy.
/ OFF
For cancelling the programme which is running or to
switch the machine off .
1) If using liquid detergents, a programme without prewash must be selected.
2) If you select the Super Quick option by pressing button 6, we recommend that you reduce the maximum load as
indicated. Full loading is possible however with somewhat reduced cleaning results.
20
Consumption values
CONSUMPTION VALUES
Programme
Energy consumption
Water consumption
(litres)
Programme duration
(Minutes)
(KWh)
White Cottons 95°
Cottons 60°
2.1
57
53
42
1.2
Cotton Energy Saving
Programme 60° 1)
1.02
For the duration of
the programmes,
please refer to the
display on the control
panel.
Cottons 40°
0.7
0.5
53
44
56
58
Synthetics 40°
Delicates 40°
0.55
0.25
Wool/ Handwash 30°
1) «Cotton Energy Saving programme » at 60°C with a load of 6 kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may
vary depending on the quantity and type of laundry, on the inlet water temperature and on
the ambient temperature.
HELPFUL HINTS AND TIPS
Sorting out the laundry
Follow the wash code symbols on each garment label and the manufacturer’s washing in-
structions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens.
Before loading the laundry
Never wash whites and coloureds together. Whites may lose their «whiteness» in the wash.
New coloured items may run in the first wash; they should therefore be washed separately
the first time.
Button up pillowcases, close zip fasteners, hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special detergent or detergent paste.
Treat curtains with special care. Remove hooks or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just water and detergent. It is therefore advisable
to treat them prior to washing.
Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a
special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine, lay the garment on a soft surface and dab
the stain with the fingertips and a cotton cloth.
Helpful hints and tips
21
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful
with rust stains which are not recent since the cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well (whites and fast coloureds only).
Grass: soap lightly and treat with bleach (whites and fast coloureds only).
Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Treat any
residual marks with bleach.
Red wine: soak in water and detergent, rinse and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the fabric first with acetone1), then with acetic
acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with deter-
gent paste.
Detergents and additives
Good washing results also depend on the choice of detergent and use of the correct quan-
tities to avoid waste and protect the environment.
Although biodegradable, detergents contain substances which, in large quantities, can up-
set the delicate balance of nature.
The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.),
the colour, washing temperature and degree of soiling.
All commonly available washing machine detergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C max) and woollens
• liquid detergents, preferably for low temperature wash programmes (60°C max) for all
types of fabric, or special for woollens only.
The detergent and any additives must be placed in the appropriate compartments of the
dispenser drawer before starting the wash programme.
If using liquid detergents, a programme without prewash must be selected.
Your appliance incorporates a recirculation system which allows an optimal use of the con-
centrated detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not ex-
ceed the «MAX» mark in the detergent dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend on the type of fabric, load size, degree of
soiling and hardness of the water used.
Follow the product manufacturers’ instructions on quantities to use.
Use less detergent if:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
1) do not use acetone on artificial silk
22
Care and cleaning
Degrees of water hardness
Water hardness is classified in so-called “degrees” of hardness. Information on hardness of
the water in your area can be obtained from the relevant water supply company, or from
your local authority. If the water hardness degree is medium or high we suggest you to add
a water softener following always the manufacturer’s instructions. When the degree of
hardness is soft, readjust the quantity of the detergent.
CARE AND CLEANING
You must DISCONNECT the appliance from the electricity supply, before you can carry out
any cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is a good idea to periodically use a water soft-
ening powder in the machine. Do this separately from any laundry washing, and according
to the softening powder manufacturer's instructions. This will help to prevent the forma-
tion of lime deposits.
After each wash
Leave the door open for a while. This helps to prevent mould and stagnant smells forming
inside the appliance. Keeping the door open after a wash will also help to preserve the door
seal.
Maintenance wash
With the use of low temperature washes it is possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash programme.
• Use a normal measure of detergent, must be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance with soap and water only, and then dry thor-
oughly.
Do not use methylated spirits, solvents or similar products to clean the cabinet.
Detergent dispenser drawer
The detergent dispenser drawer should be cleaned regularly.
Care and cleaning
23
1. To aid cleaning, the top part of the addi-
tive compartment should be removed. Re-
move the detergent dispenser drawer by
pressing the catch downwards and by
pulling it out.
2. Flush it out under a tap, to remove any
traces of accumulated powder.
3. Having removed the drawer, use a small
brush to clean the recess, ensuring that all
washing powder residue is removed from
the upper and lower part of the recess.
4. Replace the drawer and run the rinse pro-
gramme without any clothes in the drum.
Washing drum
Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap
water containing iron.
Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or
iron or steel wool.
1. Remove any rust deposits on the drum with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing to clean off any cleaning agent residues.
Programme: Short Cotton Programme at maximum temperature and add approx. 1/4
measuring cup of detergent.
24
Care and cleaning
Door seal
Check from time to time the door seal and objects
that could be trapped in the fold.
Drain pump
The pump should be inspected regularly and particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during draining due to objects such as safety pins,
coins etc. blocking the pump;
• a problem with water draining is detected (see chapter “What to do if...” for more de-
tails).
WARNING!
Before unscrewing the pump cover, switch the appliance off and remove the mains plug
from the socket.
Proceed as follows:
1. Unplug the appliance.
2. If it is necessary, wait until the water has cooled down.
3. Place a container close to the pump to
collect any spillage.
A
B
4. Release the emergency emptying hose (B),
place it in the container and remove its
cap cover.
Care and cleaning
25
5. When no more water comes out, unscrew
the pump cover (A) by turning it anti-
clockwise and remove the filter. Use pli-
ers, if necessary. Always keep a rag nearby
to dry up any water spillages when re-
moving the cover.
Clean the filter under a tap, to remove
any traces of fluff.
6. Remove foreign bodies and fluff from the
filter seat and from the pump impeller.
Check carefully whether the pump impel-
ler rotates (it rotates jerkily). If it doesn’t
rotate, please contact your Service Centre.
7. Put the cap back on the emergency emp-
tying hose and place the latter back in its
seat.
8. Replace the filter into the pump by insert-
ing it correctly into the special guides.
Screw the pump cover firmly by turning it
clockwise.
WARNING!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash cycle, always wait until the appliance has fin-
ished the cycle, and is empty. When refitting the pump cover, ensure it is securely re-tight-
ened so as to stop leaks and young children being able to remove it.
Cleaning the water inlet filters
If the appliance doesn't fill, it takes a long time to fill with water, the starting button blinks
yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..."
for more details), check if the water inlet filters are blocked .
To clean the water inlet filters:
26
Care and cleaning
1. Turn off the water tap.
2. Unscrew the hose from the tap.
3. Clean the filter in the hose with a stiff
brush.
4. Screw the hose back onto the tap. Make
sure the connection is tight.
5. Unscrew the hose from the machine. Keep
a towel nearby because some water may
flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.
Emergency emptying out
If the water is not discharged, proceed as follows to empty out the appliance:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has cooled down;
4. place a bowl on the floor and place the end of the emergency emptying hose into the
bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl
What to do if…
27
is full, put the cap back on the hose. Empty the bowl. Repeat the procedure until water
stops flowing out;
5. clean the pump if necessary as previously described;
6. replace the emergency emptying hose in its seat after having plugged it;
7. screw the pump again.
Frost precautions
If the machine is installed in a place where the temperature could drop below 0°C, proceed
as follows:
1. close the water tap and unscrew the water inlet hose from the tap;
2. place the end of the emergency emptying hose and that of the inlet hose in a bowl
placed on the floor and let water drain out;
3. screw the water inlet hose back on and reposition the emergency emptying hose after
having put the cap on again.
By doing this, any water remaining in the machine is removed, avoiding ice forming and
consequently damage to the appliance.
When you use the machine again, make sure that the ambient temperature is above 0°C.
WHAT TO DO IF…
Certain problems are due to lack of simple maintenance or oversights, which can be solved
easily without calling out an engineer. Before contacting your local Service Centre, please
carry out the checks listed below.
During machine operation it is possible that the yellow pilot light of button 7 blinks, one of
the following alarm codes appears on the display and at the same time some acoustic sig-
nals sound every 20 seconds to indicate that the machine is not working:
•
•
•
: problem with the water supply
: problem with the water draining
: door open
Once the problem has been eliminated, press the button 7 to restart the programme. If af-
ter all checks, the problem persists, contact your local Service Centre.
28
What to do if…
Problem
Possible cause/Solution
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power
socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical instal-
lation.
The main fuse has blown.
The washing machine does not start:
• Replace the fuse.
The selector dial is not correctly positioned and
the button 7 has not been pressed.
• Please turn the selector dial and press the
button 7 again.
The delay start has been selected.
• If the laundry is to be washed immediately,
cancel the delay start.
The Child safety lock has been activated.
• Deactivate this device.
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve fil-
ter are blocked.
The machine does not fill:
• Clean the water inlet filters. (See "Cleaning
the water inlet filters" for more details)
The door is not properly closed.
• Close the door firmly.
The end of the drain hose is too low.
The machine fills then empties immediately:
• Refer to relevant paragraph in «Water drain-
age» section.
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
• Clean the drain filter.
An option or a programme that ends with the
water still in the tub or a that eliminates all the
spinning phases has been selected.
The machine does not empty and/or does not
spin:
• Select the draining or the spinning pro-
gramme.
The laundry is not evenly distributed in the
drum.
• Redistribute the laundry.
What to do if…
29
Problem
Possible cause/Solution
Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Reduce the detergent quantity or use anoth-
er one.
Check whether there are any leaks from one of
the inlet hose fittings. It is not always easy to
see this as the water runs down the hose; check
to see if it is damp.
• Check the water inlet hose connection.
The drain or the inlet hose is damaged.
There is water on the floor:
• Replace it with a new one.
The cap on the filter has not been replaced or
the filter has not been properly screwed in after
cleaning action.
• Refit the cap on the filter or screw the filter
fully in.
Too little detergent or unsuitable detergent has
been used.
• Increase the detergent quantity or use an-
other one.
Stubborn stains have not been treated prior to
washing.
Unsatisfactory washing results:
• Use commercial products to treat the stub-
born stains.
The correct temperature was not selected.
• Check if you have selected the correct tem-
perature.
Excessive laundry load.
• Reduce the laundry load.
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
The door will not open:
• Wait until the symbol 9.5 has gone off.
There is water in the drum.
• Select drain or spin programme to empty out
the water.
30
What to do if…
Problem
Possible cause/Solution
The transit bolts and packing have not been re-
moved.
• Check the correct installation of the appli-
ance.
The support feet have not been adjusted
The machine vibrates or is noisy:
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the
drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has
cut in because the laundry is not evenly distrib-
uted in the drum. The laundry is redistributed
by reverse rotation of the drum. This may hap-
pen several times before the unbalance disap-
pears and normal spinning can resume. If, after
some minutes, the laundry is still not evenly
distributed in the drum, the machine will not
spin.
Spinning starts late or the machine does not
spin:
• The laundry load is perhaps to little, add
more items, redistribute the load manually
and then select the spinning programme.
The machine is fitted with a type of motor
which makes an unusual noise compared with
other traditional motors. This new motor en-
sures a softer start and more even distribution
of the laundry in the drum when spinning, as
well as increased stability of the machine.
The machine makes an unusual noise:
No water is visible in the drum:
Machines based on modern technology operate
very economically using very little water with-
out affecting performance.
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning,
make a note of the model, serial number and pur-
chase date of your machine: the Service Centre
will require this information.
Installation
31
INSTALLATION
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, careful-
ly lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
32
Installation
3. Unscrew the three bolts with the key sup-
plied with the appliance.
4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two
large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not impeded by carpets, rugs etc.
Before placing it on small tiles, apply a rubber coating.
Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or
similar materials under the machine.
Installation
33
If it is impossible to avoid positioning the machine next to a gas cooker or coalburning
stove, an insulating panel covered with aluminium foil on the side facing the cooker or
stove, must be inserted between the two appliances.
The machine must not be installed in rooms where the temperature can drop below 0°C.
The water inlet hose and the drain hose must not be kinked.
Please ensure that when the appliance is installed, it is easily accessible for the engineer in
the event of a breakdown.
Carefully level by screwing the adjustable feet in
or out. Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
After having levelled the appliance, tighten the
lock nuts.
Water inlet
An inlet hose is supplied and can be found inside the machine drum.
This appliance must be connected to a cold water supply.
Do not use the hose from your previous machine to connect to the water supply.
34
Installation
1. Open the porthole and extract the inlet
hose.
2. Connect the hose with the angled con-
nection to the machine.
Do not place the inlet hose downwards. An-
gle the hose to the left or right depending
on the position of your water tap.
3. Set the hose correctly by loosening the
ring nut. After positioning the inlet hose,
be sure to tighten the ring nut again to
prevent leaks.
4. Connect the hose to a tap with a 3/4”
thread. Always use the hose supplied with
the appliance.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the
tap, you will have to purchase a new, longer
hose specially designed for this type of use.
Installation should comply with local water
authority and building regulations require-
ments. Check the minimum water pressure re-
quired for safe operation of the appliance in
the chapter "Technical Data".
Installation
35
Water-stop device
The inlet hose is provided with a water stop de-
vice, which protects against damage caused by
water leaks in the hose which could develop due
to natural ageing of the hose. This fault is shown
by a red sector in the window «A». Should this oc-
cur, turn the water tap off and refer to your Serv-
ice Centre to replace the hose.
A
Water drainage
The end of the drain hose can be positioned in three ways:
1. Hooked over the edge of a sink using the plastic hose guide supplied with the ma-
chine.
In this case, make sure the end cannot come unhooked when the machine is emptying.
This could be done by tying it to the tap
with a piece of string or attaching it to
the wall.
2. In a sink drain pipe branch. This branch
must be above the trap so that the bend
is at least 60 cm above the ground.
3. Directly into a drain pipe at a height of
not less than 60 cm and not more than 90
cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter
of the drain hose.
The drain hose must not be kinked.
36
Electrical connection
The drain hose may be extended to a maximum of 4 metres. An additional drain hose and
joining piece is available from your local Service Centre.
ELECTRICAL CONNECTION
Information on the electrical connection is given on the rating plate on the inner edge of
the appliance door.
Check that your domestic electrical installation can take the maximum load required, also
taking into account any other appliances in use.
WARNING!
Connect the machine to an earthed socket.
WARNING!
The manufacturer does not accept any responsibility for damage or injury through fail-
ure to comply with the above safety precaution.
WARNING!
The power supply cable must be easily accessible after installing the machine.
WARNING!
Should the appliance power supply cable need to be replaced, this must be carried out
by a Service Centre.
Building-in
37
BUILDING-IN
This appliance has been designed to be built into
600
min.
the kitchen furniture. The recess should have the
dimensions shown in picture A.
Preparation and assembly of the door
596
555
560
min.
820
176,5
416
818
75
60
170
100
The machine is originally pre-arranged for the as-
sembly of a door opening from right to left.
In this case it is sufficient to screw in the hinges
(1) and the counter-magnet (6) provided with the
appliance, at the right level (Fig. B).
6
1
4
5
7
3
8
2
• Door
B
The dimensions of the door should be:
– width 595-598 mm
16-22
– thickness 16-22 mm
The height (C-Fig. C) depends on the height of
the adjacent furniture's base.
C
416
35 o
14
• Hinges
To mount the hinges it is necessary to drill two
holes (dia. 35 mm, depth 12.5-14 mm depend-
ing on the depth of door furniture) on the in-
ner side of the door. The distance between the
holes hobs fixing centres must be 416 mm.
22+1,5
595-598
The distance (B) from upper edge of the door to
the centre of the hole depends on the adjacent furniture's dimensions.
The required dimensions are given in the picture C.
The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with
the appliance.
• Mounting the door
38
Environment concerns
Fix the hinges (1) to the machine by means of the M5x15 screws (3-Fig. B). The hinges
can be adjusted to compensate for possible uneven thickness of the door.
To align the door perfectly it is necessary to loosen the screw (3-Fig. B), adjust the door
and tighten the screw again.
• Counter-magnet (6)
The appliance is prearranged for a magnetic
closure of the door. To enable a correct opera-
tion of this device, it is necessary to screw the
counter-magnet (6) (steel disk + rubber ring)
into the inner side of the door.
4
6
Its position must correspond to the magnet (4)
on the appliance (see picture D).
8
If the door has to be opened from left to right, in-
vert the position of the plates (7), the magnet (4)
and the plate (5) (Fig. B and E). Mount the coun-
ter-magnet (6) and the hinges (1) as previously
described.
6
1
4
5
7
3
8
2
ENVIRONMENT CONCERNS
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local council, your household waste disposal service or the shop where
you purchased the product.
Packaging materials
The materials marked with the symbol
are recyclable.
39
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of them properly in appropriate collec-
tion containers.
Ecological hints
To save water, energy and to help protect the environment, we recommend that you follow
these tips:
• Normally soiled laundry may be washed without prewashing in order to save detergent,
water and time (the environment is protected too!).
• The machine works more economically if it is fully loaded.
• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can
then be washed at a lower temperature.
• Measure out detergent according to the water hardness, the degree of soiling and the
quantity of laundry being washed.
|