Model PRO 2032
OWNER’S MANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE
Congratulations on your purchase of the PRO 2032 automotive Keyless Entry
Upgrade Alarm System. This system is a state-of-the-art auto security system that
is designed to automatically arm and disarm when it receives a command from your
existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.
NOTE: This unit has the capability to operate an optional siren, the vehicle horn, or
both. Where referenced (the siren will chirp) the siren may chirp, the horn
may beep or both may occur.
ARMINGTHESYSTEM:(ACTIVE)
1. Turn the ignition key off, exit the vehicle and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren will chirp one time, the parking lamps will flash one time, and the red
dash mounted LED will begin to slowly flash, indicating that the system is
ARMED.
NOTE: If the unit beeps three times when arming, then one of the entry points
(hood, trunk, or doors) has been left opened. Closing the hood, trunk, or
door will correct the problem and the system will emit a single chirp to
confirm that the problem has been corrected. Additionally, if illuminated
entry is a feature of the Factory Keyless Entry system, the alarm may chirp
3 times every time the system is armed and chirp one additional time
when the interior light turns off to confirm that all trigger zones are fully
operational.
4. Any time the door lock switch in the vehicle is used to lock the doors while the
ignition key is turned off, the system will immediately arm. To lock the doors after
entering the vehicle, make sure the ignition key is switched on first. Turning the
ignition key on first will stop the system from arming.
ARMINGTHESYSTEM:(PASSIVE)
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The dash mounted LED will begin to flash rapidly, indicating that the system is
automatically ( passively ) arming. As an added convenience, the 30 second
automatic passive arming will not begin until all doors are closed, allowing
passengers to exit the vehicle at their convenience.
Released 7-23-01.
128-6132
1 OF 8
INTRUSIONWARNINGSIGNALS:
The system will inform you if an intrusion attempt has occurred while you were away
from the vehicle. If an intrusion attempt has occurred, the siren and or horn will beep
four times when the system is disarmed. The vehicle’s parking lights will also flash
three times to indicate an intrusion has occurred.
Enter the vehicle and observe the dash mounted LED for further information.
1. If the LED is flashing one time...pause...one time...pause...etc., then an intrusion
attempt was made to a voltage sensing, light activated entry point, or to an
optional sensor that has been connected to zone 1.
2. If the LED is flashing two times...pause...two times...pause...etc., then an
intrusion attempt was made to the hood or trunk, or to an optional sensor that
has been connected to zone 2.
3. If the LED is flashing three times...pause...three times...pause...etc., then an
intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory and will only
be erased when the ignition key is turned to the "on" position.
OPERATINGTHEEMERGENCYPANIC:
The buttons on your keychain transmitter will allow you to immediately activate the
alarm in emergency situations. To use the remote panic switch;
1. Press the unlock, then lock, then unlock buttons on your keychain transmitter
within 3 seconds. The alarm will immediately sound and continue to sound for
30 seconds.
2. To stop the alarm before the 30 second cycle has expired, simply press and
release the unlock button on your keychain transmitter.
USINGTHEVALETSWITCH:
The valet switch allows you to temporarily bypass all alarm functions, eliminating
the need to hand your transmitter to parking attendants or garage mechanics.
When the system is in valet mode, all alarm functions are bypassed, however the
remote panic feature and remote door locks will remain operational. To use the
valet mode, the system must first be disarmed either by using your keychain
transmitter, or by activating your personalized manual override code.
TO ENTER THE VALET MODE:
1. Disarm the unit by use of the factory transmitter or by use of the manual override
sequence.
2. Turn the ignition switch to the "On" position.
3. Press and hold the valet/override pushbutton switch for 5 seconds. The LED
turns on, indicating valet mode has been successfully entered.
TOEXITVALET:
With the ignition switch in the on position, press and release the valet/override
pushbutton switch one time. The LED turns off indicating the valet mode has
successfully been exited.
3
128-6132
3 OF 8
MANUALLYOVERRIDINGYOUR SYSTEM
USING THE VALET SWITCH MANUAL OVERRIDE
Your Security System can be disarmed without the use of the keychain transmit-
ter. This is necessary, since you will need the ability to operate your vehicle if the
transmitter is lost or its battery fails. If your system has been selected for Valet
Switch manual override as indicated on the last page of this manual, to by-pass
the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and release the valet pushbutton switch.
The alarm system will stop sounding. You can now start and operate the vehicle
normally.
Typically this override mode is used only if the transmitter has become inopera-
tive. If this is the case, you may want to enter the valet mode until a operating or
replacement transmitter is available.
PROGRAMMING THE CUSTOM CODE MANUAL OVERRIDE
Unlike override switches easily found, and defeated, this security system allows
the consumer to program a personal override code, offering a higher level of
security. To take advantage of this option, programmable feature # 9 must be
selected for the Custom Code Option. Consult your installation center for pro-
gramming details. The system comes from the factory with a pre-programmed
override code of 11. To change this default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override switch, 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off
then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code, by
flashing the LED, first indicating the 10ths digit, pause and then the units digit.
The unit will report the new code three times with a one second pause between
each code, then the system will begin arming. If the LED flash pattern reports the
previously stored code, the new code was not entered correctly. Please repeat
steps 1 through 7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recog-
nize a 0 (Zero), or no digit entered in any place, units or tenths.
4
128-6132
4 OF 8
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you would
do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency over-
ride sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override switch, 3 times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the push button switch to set
the tenths digit.
(As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the push-button, turn the igntion switch
off then on.
7. Within 10 seconds, begin to press and release the push button switch to set
the units digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the off position. Immediately observe the LED flash
pattern.
You will note the LED flashing five times, pause, and then flash two times, pause.
This pattern will be repeated three times indicating the new code (52) has been
accepted and stored in memory.
NOTE: If after step 7, the LED flashes a code other than what was just entered,
this indicates that the code has not been changed. You will have to repeat
steps 1 through 7 above being certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0
(Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.
MANUALLYOVERRIDINGYOUR SYSTEM:
USING THE CUSTOM CODE OVERRIDE
Assuming the override code programmed has not been changed and the default
override code of 11 is in the system's memory.
1) Enter the vehicle and turn the ignition switch to the on position.
NOTE: The siren will sound.
2) Within 5 seconds, press and release the pushbutton switch 1 time.
3) Within 5 seconds, turn the ignition switch off then on.
4) Within 5 seconds, press and release the pushbutton switch 1 time.
5) Turn the ignition switch off then on and start the vehicle.
5
128-6132
5 OF 8
NOTE: If you have changed the programmed override code then substitute your
new code tenths for step 2 above, and units for step 5 above.
ADDITIONALREMOTEFUNCTION:
This system allows the control of any one of the following optional accessories;
Remote Car Starter
Remote Window Closure
Remote Window Open
To operate the optional accessory;
1. Press the lock, then unlock, then lock buttons on your keychain transmitter within
3 seconds.
2. The optional accessory will immediately activate.
OPTIONALAUTOLOCK/UNLOCKFEATURE:
If your existing factory installed keyless entry system did not include the automatic
door lock and unlock feature, then this feature can be activated from the PRO 2032
upgrade module. When this accessory has been added, any time the ignition key
is turned to the on position and all vehicle doors are closed, the doors will lock in
4 seconds. Additionally, any time the ignition key is turned to the off position, the
doors will unlock.
ELIMINATINGTHEARM/DISARMCHIRPS:
The normal arming and disarming confirmation chirps can easily be turned off using
the valet pushbutton switch. To do this;
1. Turn the ignition key on and then off.
2. Within 10 seconds of turning the ignition key off, press and release the valet
switch 3 times.
3a. If, before proceeding with step 1, the chirps were on, then you will hear 2 chirps
to indicate that the chirps have been turned off.
b. If, before proceeding with step 1, the chirps were off, then you will hear 1 chirp
to indicate that the chirps have been turned on.
4. If the unit emits 2 chirps, regardless of your action based on the above
instructions, the chirps have been eliminated in the units feature selections by
your installing dealer. Please consult with them on allowing access to this
feature.
NOTE: Whenever the Arm/Disarm chirps are by-passed, the 3 chirp defective
zoneandthe4chirpintrusionindicatorwillalwaysoperate. Thisfeature
will always warn you if a door was left ajar when arming, or the vehicle
was tampered with in your absence.
6
128-6132
6 OF 8
PRO 2032
SYSTEM FUNCTIONS AT A GLANCE
DASHLEDINDICATORS
RAPIDFLASHING.............................................................................PASSIVEARMING
SLOWFLASHING.................................................................................................ARMED
OFF...................................................................................................................DISARMED
ONSOLID....................................................................................................VALETMODE
3FLASH...PAUSE.............................................................................INTRUSIONZONE
2FLASH...PAUSE..........................................................................INTRUSIONZONE2
1FLASH...PAUSE..........................................................................INTRUSIONZONE1
CHIRPINDICATORS
1CHIRP*........................................................................................................ARM
2CHIRPS*......................................................................................................DISARMED
3CHIRPS....................................................................................ARMWITHINTERIOR
LIGHT ON OR DOOR AJAR
4CHIRPS........................................................................DISARMAFTERINTRUSION
2SHORTTHEN1LONG.............................................DISARMAFTER10MINUTES
PASSIVEARMOVERRIDE
4SHORTTHEN1LONG.............................................DISARMAFTER10MINUTES
PASSIVE ARM OVERRIDE WITH INTRUSION
* These chirps are optional and can be de-activated
PARKINGLIGHTS
1FLASH.......................................................................................................................ARM
2FLASH................................................................................................................DISARM
3FLASH............................................................................DISARMAFTERINTRUSION
Your System Has These Features Activated:
! Starter Disable When Armed
! Passive Arming
! Key Activated Door Unlock
! Custom Code Override
! Remote Car Start
! Remote Window Closure
! Key Activated Door Lock
! Valet Override
! Shock Detector
! Voltage Sense
7
128-6132
7 OF 8
Audiovox Electronic Corp.
150 Marcus Blvd.
Hauppauge, N.Y. 11788
128-6132
128-6132
8 OF 8
|