Heat Exhaust kit
Installation manual
NH-12 series and NW-xx series
R9843115
R59770445/01
05/04/2012
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2002/96/EC governing waste from electrical and electronic
equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to
a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly
to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. For
details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser
must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco
must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component
of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties
guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,
in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are
system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by
the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
Table of contents
TABLE OF CONTENTS
1. Exhaust kit description............................................................................................ 3
1.1 Domain of application ................................................................................................................ 3
1.2 Specifications ......................................................................................................................... 3
1.3 Kit content ............................................................................................................................ 4
2. Installation of the Exhaust ....................................................................................... 7
2.1 Preparations ......................................................................................................................... 7
2.1.1 Removing the rear cover ...................................................................................................... 7
2.1.2 Preparing the rear cover ...................................................................................................... 7
2.2 Mounting the parts.................................................................................................................... 8
Index...................................................................................................................... 11
R59770445 HEAT EXHAUST KIT 05/04/2012
1
Table of contents
2
R59770445 HEAT EXHAUST KIT 05/04/2012
1. Exhaust kit description
1. EXHAUST KIT DESCRIPTION
About this manual
This manual describes the Heat Exhaust kit with part number R9843115 and the way to install it on a projector.
Overview
•
•
•
1.1 Domain of application
What can be done ?
The Heat Exhaust kit allows to connect an external tube system to the projector in order to transport the exhaust hot air outside the
projection area.
Each projector has 2 exhausts:
1. left exhaust;
2. right exhaust.
1
2
Image 1-1
Exhaust location
One can decide to connect only one or both exhausts.
Projector range
The Heat Exhaust kit is intended to be used on the following projector ranges:
•
•
•
(Galaxy) NH-12;
(Galaxy) NW-12;
Galaxy NW-7.
1.2 Specifications
Heat dissipation per projector
The maximum heat dissipation of the projector when it runs at full power is 2800 W or 9560 BTU/h. This value can be different,
depending on the power rate of the lamp (i.e. Economy mode or Normal mode).
Outlet temperature
The maximum temperature of the air at the outlet is 60° C when the projectors run at full power and assuming the environmental
temperature to be 20° C maximum. All elements in the air extraction need to resist at least a temperature of 60° C for long duration.
Air speed
For acoustical reasons, an air speed of 6 m/s is typically recommended in an office/auditorium environment. In a display system
where the projectors and the collector are not situated inside the projection room, the air speed in the tubes between projector outlet
and "collector" tube can be slightly higher.
R59770445 HEAT EXHAUST KIT 05/04/2012
3
1. Exhaust kit description
Flow rate
The flow rate varies, as the speed of the internal fans changes depending on the power rate of the projector and depending on the
ambient temperature. The maximum flow rate is 50 l/s per projector. The airco can be designed to extract 50 l/s per projector at all
time.
The following table lists the air flow at both exhausts in different lamp power modes:
Exhaust air flow
Economy lamp mode
3,3 l/s
20,3 l/s
Normal lamp mode
6,4 l/s
1
2
31,3 l/s
Outlet tube
The external diameter of the outlet tubes is 100 mm, which matches the common size of 100 mm for flexible extraction pipes. For a
flow rate of 50 l/s, this results in an air speed of 6,4 m/s.
The extraction pipes are not included in this kit
Extraction control
No air extraction control is required. It is no problem that air is sucked through the projectors even when they are switched off.
Please note that heat dissipation in the room is obviously less when all projectors are switched off. For good
stability of the system, the projection room should be kept to the same temperature level, no matter if the
projectors are on or off. Therefore the airco must be controlled in some way by temperature sensors in the
projection room.
1.3 Kit content
Bill of material
The following table gives an overview of the parts contained in the Heat Exhaust kit:
Name
Qty
Illustration
Right exhaust bracket
1
Left exhaust bracket
1
4
R59770445 HEAT EXHAUST KIT 05/04/2012
1. Exhaust kit description
Name
Qty
Illustration
Right exhaust housing
1
Left exhaust housing
1
Fastening ring
2
-
-
Screw 3,9 x 10
Screw 4 x 8
8
8
Table 1-2
Kit content
R59770445 HEAT EXHAUST KIT 05/04/2012
5
1. Exhaust kit description
6
R59770445 HEAT EXHAUST KIT 05/04/2012
2. Installation of the Exhaust
2. INSTALLATION OF THE EXHAUST
Overview
•
•
2.1 Preparations
Overview
•
•
2.1.1
Removing the rear cover
Necessary tools
Philips Ph2
How to remove the rear cover?
1. Remove the fixing screw
Image 2-1
Rear cover: fixing screw
2. Lift the back side of the rear cover and pull it backward to remove it
Image 2-2
Tilt the back side of the rear cover
Image 2-3
Pull the rear cover backward
Image 2-4
Rear cover removed
2.1.2
Preparing the rear cover
Necessary tools
•
Marker pen
•
Drill with diameter 3,3 mm
R59770445 HEAT EXHAUST KIT 05/04/2012
7
2. Installation of the Exhaust
Necessary parts
•
•
•
Left outlet bracket
Right outlet bracket
Projector rear cover
How to prepare the cover mount the outlet bracket?
1. Position the outlet brackets as indicated below (the brackets must interfere with the open exhaust area) and mark the position of
the 8 foreseen fixation holes.
Image 2-6
Image 2-5
2. Drill 3,3 mm diameter holes on the 8 marked positions.
Image 2-7
2.2 Mounting the parts
Necessary tools
•
Torx
•
Philips Screwdriver
Necessary parts
•
•
•
•
•
•
•
•
8 delivered screws
Left outlet bracket
Right outlet bracket
Projector rear cover
Left outlet housing
Right outlet housing
Rings
Tube(s)
How to mount the brackets and the outlet housings?
1. Mount the left and the right bracket using the 8 screws.
8
R59770445 HEAT EXHAUST KIT 05/04/2012
2. Installation of the Exhaust
Image 2-8
2. Mount and fix the left and right housings on the brackets using the 8 screws.
Image 2-9
How to connect a tube to the exhaust?
1. Mount the rings without fastening them.
Image 2-10
2. Mount and fix the assembled cover on the projector.
Image 2-11
3. Mount the tube(s) and fasten the rings.
R59770445 HEAT EXHAUST KIT 05/04/2012
9
2. Installation of the Exhaust
Image 2-12
10
R59770445 HEAT EXHAUST KIT 05/04/2012
|
