Behringer Musical Instrument Amplifier BVT4500H User Manual

User Manual

A50-52113-00003

ULTRABASS BVT4500H/BVT5500H

Foreword

Table of contents

1. Introduction......................................................................... 4

Dear customer,

1.1 The Design Concept .................................................... 4

Welcome to the team of

ULTRABASS users and

thank you very much for

expressing your confi-

dence in BEHRINGER

products by purchas-

ing the BEHRINGER

BVT4500H/BVT5500H.

1.2 Before you get started.................................................. 4

1.2.1 Shipment............................................................. 4

1.2.2 Initial operation ................................................... 4

1.2.3 Online Registration ............................................. 4

2. Front pane l .......................................................................... 5

3. Rear pane l ........................................................................... 6

4. About speaker impedance................................................. 7

5. Setup exampl e .................................................................... 8

Writing this foreword for

you gives me great plea-

sure, because it repre-

sents the culmination of

many months of hard work

delivered by our engineer-

ing team to achieve a very

ambitious goal: to pres-

ent an outstanding bass

workstation that gives

you maximum flexibility

and performance with its

6. The signal pat h ................................................................... 8

6.1 INPUT .......................................................................... 8

6.2 TUNER......................................................................... 8

unique sound character and broad range of functions.

6.3 LINE OUTPUT ............................................................. 8

6.3.1 PRE .................................................................... 8

6.3.2 POS T .................................................................. 8

The task of designing our new BVT4500H/5500H certainly meant

a great deal of responsibility, which we assumed by focusing on

you, the discerning user and musician. Meeting your expectations

also meant a lot of work and night shifts. But it was fun, too. De-

veloping a product usually brings a lot of people together. What a

great feeling it is when all who participated in such a project can

be proud of what they’ve achieved.

6.4 EFFECTS LOOP.......................................................... 8

6.4.1 SEND and RETURN........................................... 8

6.4.2 SEND only (BVT5500H only).............................. 9

6.4.3 RETURN only ..................................................... 9

It is our philosophy to share our enjoyment with you, because you

are the most important member of the BEHRINGER team. With

your highly competent suggestions for new products you’ve made

a signiﬁcant contribution to shaping our company and making it

successful. In return, we guarantee you uncompromising quality

as well as excellent technical and audio properties at an extremely

reasonable price.All of this will enable you to give free rein to your

creativity without being hampered by budget constraints.

6.5 INSERT CHANNE L ...................................................... 9

6.5.1 PREAMP OUTPUT............................................. 9

6.5.2 POWER AMP I N ................................................. 9

7. Audio connector s ............................................................... 9

8. System block diagram ..................................................... 10

9. Speciﬁcation s ................................................................... 11

10. Warranty ......................................................................... 12

We are often asked how we manage to produce such high-quality

devices at such unbelievably low prices. The answer is quite

simple: it’s you, our customers! Many satisﬁed customers mean

large sales volumes, enabling us to get better purchasing terms

for components, etc. Isn’t it only fair to pass this beneﬁt on to you?

Because we know that your success is our success, too!

I would like to thank everyone who has made the BVT4500H/5500H

possible. You have all made your own personal contributions, from

the developers and the many other employees at this company,

to you, the BEHRINGER user.

My friends, it’s been worth the effort!

Thank you very much,

Uli Behringer

ULTRABASS BVT4500H/BVT5500H

Blown fuses must be replaced by fuses of the correct

rating! Please refer to the "SPECIFICATIONS" section

for the applicable rating.

1. Introduction

With the BVT4500H/5500H you have acquired a pro-level ampliﬁer

from our ULTRABASS series. This classic bass amp combines

an uncompromising, “cutting-through” sound with a full range of

CAUTION!

Before changing the fuse, switch off the device and

pull the plug to avoid electric shock or damage to the

device.

sound-shaping features.

1.1 The Design Concept

Over the past few years, ﬂexibility has become important. Bass

For connection to the mains use the enclosed power cord with cold

connector which complies with the relevant safety regulations.

players must now offer a broad range of sounds and play in differ-

ent venues: home studios, professional studios, and live concerts.

Additionally, the world of electric bass playing has changed. New

effects devices and basses, with ﬁve or six strings, are launched

all the time. There is also the desire to create one’s own, “unique”

sound—which can only be achieved with innovative ampliﬁers.

Please make sure that all devices are properly grounded.

For your own safety, never remove or disable the ground

conductors from the devices or on the power cords. The

unit must always be connected to the mains outlet with

a protective grounding connection.

In response to these dual needs (ﬂexibility and individuality), the

BVT4500H/5500H offers you:

Please ensure that only qualiﬁed personnel install and

operate the BVT4500H/BVT5500H. During installation

and operation the user must have sufﬁcient electrical

contact to earth. Electrostatic charges might affect the

operation of the unit.

= TONE and GRAPHIC EQ features—for shaping and reﬁning

sound.

= VTC (Virtual Tube Circuitry)—adding the warmth of vintage

tube circuitry to sound.

= Jacks for connecting the BVT4500H/5500H to effects pro-

cessors, mixers/recording units, other preamps, and other

power amps.

WARNING!

Extreme output volumes may damage your hearing and/

or your loudspeakers. Turn down all volume and level

controls before you switch on the unit. Always set the

volume to an appropriate level.

= 2 types of speaker jacks: ¼" TS and compatible with Neutrik

Speakon connectors.

1.2 Before you get started

1.2.1 Shipment

Important notes concerning installation

Your product was carefully packed at the factory to ensure safe

transport. Nevertheless, if the box is damaged inspect the unit

immediately for signs of damage.

The sound quality may diminish within the range of pow-

erful broadcasting stations and high-frequency sources.

Increase the distance between the transmitter and the

device and use shielded cables for all connections.

If the unit is damaged please do NOT return it to us,

but notify your dealer and the shipping company im-

mediately; otherwise, claims for damage or replacement

may not be granted.

1.2.3 Online Registration

Please register your new BEHRINGER equipment right after your

purchase by visiting http://www.behringer.com and read the terms

and conditions of our warranty carefully.

We recommend that you use a ﬂight case to give the unit

optimum protection during use or transport.

Should your BEHRINGER product malfunction, it is our intention

to have it repaired as quickly as possible. To arrange for warranty

service, please contact the BEHRINGER retailer from whom the

equipment was purchased. Should your BEHRINGER dealer

not be located in your vicinity, you may directly contact one of

our subsidiaries. Corresponding contact information is included

in the original equipment packaging (Global Contact Information/

European Contact Information). Should your country not be listed,

please contact the distributor nearest you. A list of distributors

can be found in the support area of our website (http://www.

behringer.com).

Always use the original box to prevent damage during

storage or transport.

Make sure that children cannot play unsupervised with

the unit or its packaging.

Please ensure proper disposal of all packing

materials.

1.2.2 Initial operation

Registering your purchase and equipment with us helps us process

your repair claims more quickly and efﬁciently.

Ensure adequate air supply and to avoid overheating do not place

the unit near radiators etc.

Thank you for your cooperation!

Before you connect your BVT4500H/5500H to the mains, please

make sure that your local voltage matches the voltage required

by the unit.

CAUTION: The following applies only to BVT versions that can

be switched between 120 V and 230 V: The fuse holder on the

mains connector has 3 triangular markings. Two of these triangles

opposing each other. The device is set to the operating voltage

printed next to these markers and can be set to another voltage

by turning the fuse holder by 180°.

Please note that when operating the unit at 120 V, a

higher fuse rating is required. Blown fuses must be

replaced by fuses of the correct rating!

If you set the unit to a different mains voltage, be sure

to use a fuse of the correct type and rating. Please refer

to the “SPECIFICATIONS” for details.

Introduction

ULTRABASS BVT4500H/BVT5500H

2. Front panel

Fig. 2.1: BVT4500H front panel

Fig. 2.2: BVT5500H front panel

This section describes how to use the front panel of the BVT4500H

and the BVT5500H, illustrated on the previous page and above.

{8} GAIN control: Use this control to boost or cut the level of the

input signal.

{1} POWER switch: Use the POWER switch to turn on your

BVT4500H/5500H. The POWER switch should always be

in the “Off” position when you are about to connect your unit

to the wall socket or disconnect it.

{9} PEAK LED: At various points in the signal path, the BVT

monitors the level of the audio signal. When the level is too

high, the PEAK LED warns that clipping can occur.

If the LED:

Switch-on thumps can damage your hearing and your

speakers. Before you connect the BVT to the mains,

ensure that it is turned off.

= occasionally illuminates, the BVT clips only some peaks in the

audio signal. Occasional clipping does not reduce the sound

quality and shows that the signal is strong enough.

= never illuminates, the BVT does not clip any signal peaks in

the audio signal. The audio signal is probably too weak to

make use of the full dynamic range. Increase the GAIN {8}

setting until the PEAK LED lights up only occasionally, at the

strongest signal peaks.

{2} VTC LED: When the BVT is off, this LED is not illuminated.

When it is on, this LED is illuminated and indicates that the

amp is activated for use. VTC is BEHRINGER’s analog tech-

nology that emulates the warmth of vintage tube circuitry.

INPUT features

= constantly illuminates, the BVT clips a large part of the audio

signal and you will hear a distortion. Lower the GAIN setting

and check for extreme fader or control settings.

To input an audio signal to the BVT, use features {3} - {7}, as

follows:

{3} 0 dB jack: To connect an electric bass to the BVT, use this ¼"

mono jack (unbalanced). Basses with active pickups create

high-level signals.

TONE features

“Tone” refers to the presence and quality of these frequency bands

of an audio signal:

If your bass includes an active pickup and you work with:

= bass: from 30 to 200 Hz

= the BVT4500H, use the PAD button {4} to reduce the input

= mid-range: from 200 to 2 000 Hz

= treble: from 2 000 Hz to 20 kHz

audio signal.

= the BVT5500H, use the -15 dB jack {5}instead of the 0 dB

jack.

The BVT offers controls to effectively tailor the sounds to your

needs by cutting or boosting speciﬁc bands. To adjust the tone,

use features (10) - (13), as follows:

{4} PAD button (BVT4500H only): If the PEAK LED {9} con-

stantly illuminates and the GAIN control {8} is set to 0 (zero),

the input level of the audio signal is too high. In this case,

press this button to activate the pad. The pad reduces the

input sensitivity by 15 dB.

(10) VOICING control (BVT5500H only): To select the tone you

want, turn this knob to one of the following presets.

The BVT5500H equalizes the audio signal for you.

= 1: Prominent bass and treble tones (scooped mids).

= 2: Smooth and warm treble tones (passive tone).

= 3: Flat, natural bass tones (no equalization).

= 4: Bright treble tones.

{5} -15 dB jack (BVT5500H only): To connect an active bass to

the BVT5500H, use this ¼" mono jack (unbalanced). Using

this jack will give you a lower input sensitivity as compared

with the 0 dB jack.

{6} MUTE button (BVT5500H only): Use this button if you want

to tune a bass without hearing the tone. This feature mutes

the main signal path, but not the TUNER output.

= 5: Flat, natural bass tones that are not muddy (bass rolloff).

(11) - (13)BASS, MID, and TREBLE controls: For each tone

(bass, mid-range, and treble) that you can emphasize or

de-emphasize, the BVT includes a single TONE control.

{7} OVERDRIVE button (BVT5500H only): Use this button to

add a distorted texture to the audio signal. This feature

“overdrives” the BVT5500H preamp.

Front panel

ULTRABASS BVT4500H/BVT5500H

To emphasize a tone, you can turn the relevant tone control

toward 10 (maximum boost). Alternatively, you might con-

sider lowering adjacent bands. To de-emphasize a tone,

you can turn the relevant tone control toward 0 (maximum

cut).

(16) LEVEL fader (BVT5500H only): To compensate possible

level changes of the equalized signal, slide this control

between +12 and -12. At “0” level, the BVT5500H neither

boosts nor cuts the equalized signal.

(17) EFFECTS MIX control (BVT5500H only): If you created an

effects loop, use this control to adjust the dry-wet mix.

When you choose to cut rather than boost an audio

signal, you protect audio equipment from high signal

levels (clipping) and preserve valuable headroom.

As you turn this control toward:

= 0 (zero), you hear more of the dry signal (without effects). At

zero, you hear only the dry signal.

GRAPHIC EQ features

= 10, you hear more of the wet signal (effects). At 10, you hear

With the TONE controls ((10) - (13)) discussed above, you em-

phasize and de-emphasize three fairly wide frequency bands.

However, with the GRAPHIC EQ features, you can emphasize

and de-emphasize 9 more narrow frequency bands. This lets you

reﬁne the sound that you created with the TONE controls. The

GRAPHIC EQ features include (14)-(16):

only the wet signal.

For details about creating an effects loop, see 3. REAR PANEL

((29) - (30)).

MASTER features

(18) MASTER control: To adjust the speaker volume and the

level of the PREAMP OUTPUT, turn this control toward 0 (no

volume/level) or, alternatively 10 (maximum volume/level).

(14) EQ ON button: To turn graphic EQ and level features, push

this button.

(15) EQ faders: If you activated the frequency-band faders (14),

you can use each one to emphasize and de-emphasize

a speciﬁc frequency band. The center frequency of each

frequency band is displayed directly above the relevant

fader.

(19) LIMITER button: The limiter reduces only the signal peaks

that can overdrive the POWER AMP and distort the audio

signal. The limiter prevents the BVT4500H/5500H from

clipping these signal peaks. To activate or alternatively

deactivate the limiter, push this button.

To emphasize (boost) a frequency band, slide the relevant

fader up. Alternatively, slide the faders for the surrounding

frequency bands down.

Because high signal peaks can damage loudspeakers, it

is recommended to activate the limiter and not to play at

full volume for a long time without ear protection.

To de-emphasize (cut) a frequency band, slide the relevant

fader down.Alternatively, slide the faders for the surrounding

frequency bands up.

(20) LIMIT LED: When the limiter is activated, this LED is

illuminated.

Cutting rather than boosting a frequency band protects

audio equipment from high signal levels (clipping) and

preserves valuable headroom.

3. Rear panel

Fig. 3.1: BVT4500H/BVT5500H rear panel

This chapter describes how to use the rear panel of the BVT4500H

and the BVT5500H, which includes the same features. Figure 3.1

illustrates these features.

Do not block the ventilation openings that cover the

fan.

PARALLEL SPEAKER OUTPUT

To effectively use the jacks on the rear panel, you need

to know about the BVT signal path. For details, refer to

the secion “THE SIGNAL PATH”.

Via the following jacks, you can simultaneously connect up to 3

speakers directly to the BVT:

(25) Two ¼" TS (mono, unbalanced) jacks.

(21) Serial number: To register your unit, you will need this unique

(26) A single Neutrik Speakon compatible jack, for high-power

loudspeakers. The pin designation of the speaker is

pins 1+ and 1-. For details, refer to the chapter “AUDIO

CONNECTORS”.

identiﬁer.

(22) Fuse compartment: For details about the appropriate fuse

type, refer to the “SPECIFICATIONS”. See also chapter

1.1.2. Replace this fuse only with the type speciﬁed for your

country.

If you use a single speaker or a high-power speaker, connect

this speaker to the Neutrik Speakon compatible jack. To prevent

electrical shock and ensure the correct polarity, this jack locks an

audio plug in place.

(23) Power connector: To power the BVT4500H/5500H, plug the

power cord in thisAC connector. The power cord comes with

the BVT.

Before you connect speakers to the BVT4500H/5500H,

turn it off.

Attention: The POWER switch does not fully discon-

nect the unit from the mains. Unplug the power cord

completely when the unit is not used for prolonged

periods of time.

(24) Fan: This fan prevents the BVT4500H/5500H from

overheating.

Rear panel

ULTRABASS BVT4500H/BVT5500H

Your speaker cabinets should have a sufﬁcient power

rating (BVT4500H: > 450 W, BVT5500H: > 550 W) and

preferably a total impedance of 4 Ω or higher. Too high

a load impedance will decrease the output power rat-

ing of the power stage. For details, refer to the chapter

“ABOUT SPEAKER IMPEDANCE”.

4. About speaker impedance

The total impedance of the speakers that you connect to the

BVT affects the power output of the BVT. The minimum speaker

impedance is 4 Ω. When the total load is 4 Ω, the BVT supplies

the optimal power.

(27) POWER AMP INPUT: To connect an external preampliﬁer

How to calculate the speaker impedance

to the BVT, use this ¼" TS jack.

When using more than one speaker and each connecting to an-

other BVT speaker jack, the speakers are connected in parallel.

To calculate the resulting total impedance of the speakers, use

the following formula—

(28) PREAMP OUTPUT: To connect an external power ampliﬁer

to the BVT, use this ¼" TS jack.

EFFECTS LOOP jacks

To connect the BVT4500H/5500H to an effects processor you can

use one or, alternatively both of these jacks ((29)- (30)). Keep in

mind that the BVT4500H and the BVT5500H do not process effects

in the same way. For details, see “THE SIGNAL PATH”.

—where Z₁, Z₂etc. are each the impedance of a single speaker

and Z_totalis the resulting impedance of all speakers.

(29) RETURN jack: To send an audio signal from an effects

processor to the BVT, use this ¼" TS jack.

For two speakers (Z₁and Z₂), the formula reads as:

(30) SEND jack: To send an audio signal from the BVT to an

effects processor, use this ¼" TS jack.

Z₁⋅ Z₂

Z₁+ Z₂

Z_total

LINE OUTPUT features

To send an audio signal from the BVT to a mixer or a recording

unit, use the LINE OUTPUT features ((31) - (34)), as follows:

Via the formula, you get a 4 Ω load with:

= one 4 Ω speaker

(31) LEVEL control: To adjust the level of any LINE OUTPUT,

turn this knob toward min (no level) or, alternatively max.

= two 8 Ω speakers

The value of the max setting depends on what you selected via

the PRE/POST button (33). If you selected:

= one 8 Ω speaker and two 16 Ω speakers

As the speaker impedance decreases, the output power

of the BVT increases. High output power can damage

your speakers. As the speaker impedance increases,

the output power of the BVT decreases.

= PRE: max is ~ 0 dB.

= POST: max is ~ 10 dB.

(32) GND LIFT button: To manage the ground connection be-

tween the BVT and a mixer/recording unit, use this button.

When this button is:

= pushed out, you maintain a ground connection that prevents

electrostatic charges from interfering with an audio signal.

= pushed in, you break the ground connection. Do this only when

ground-loop hum interferes with an audio signal.

(33) PRE/POST button: To select the type of signal you want to

send to a mixer/recording unit, use this button.

When this button is:

= pushed out (PRE EQ and effects), the BVT does not apply any

preamp features (TONE/EQ/EFFECTS) to the audio signal.

= pushed in (POST EQ and effects), the BVT applies all preamp

features to the audio signal.

For details, see “THE SIGNAL PATH”.

(34) BALANCED OUTPUT: To connect the BVT to the mic input

on a mixer or, alternatively to a recording unit, use this XLR

jack (balanced).

Before you connect the BVT4500H/5500H to mic input

on a mixer, turn off the phantom power on the relevant

channel of the mixer.

(35) TUNER OUT jack: To connect the BVT4500H/5500H to an

electronic tuner, use this ¼" TS jack.

To tune while muting the PARALLEL SPEAKER OUTPUTs, do

one of the following. If you work with:

= the BVT4500H, turn the MASTER control to 0 (minimum

setting).

Alternatively, you can use the tuner’s mute feature: Connect

EFFECTS SEND (30) to the tuner input and EFFECTS RE-

TURN (29) to the tuner output. When you:

= activate the mute feature on the tuner, the tuner does not

send the audio signal to the RETURN jack.

= deactivate the mute feature on the tuner, the tuner sends

the audio signal to the RETURN jack. The audio signal

follows the signal path to the PARALLEL SPEAKER

OUTPUTs.

= the BVT5500H, activate the mute feature {6}.

About speaker impedance

ULTRABASS BVT4500H/BVT5500H

5. Setup example

6. The signal path

The following illustration provides an example of how to set up

the BVT5500H.

This section provides what you need to know to effectively use

the BVT control elements and connection jacks. For an overview

of the possible paths your signal may take, refer to the illustration

in the section “SYSTEM BLOCK DIAGRAM”.

In general, the signal path of the BVT can be split into two

phases:

1) Pre-Ampliﬁcation, which starts at the INPUT jack ({3},{5})

and ends immediately at the PREAMP OUTPUT jack (28).

2) Power ampliﬁcation, which starts at the POWER AMP IN

jack (27)and ends at the PARALLEL SPEAKER OUTPUT

jacks ((25),(26)).

Note that only the PARALLEL SPEAKER OUTPUTs carry a

fully ampliﬁed signal while the other output jacks carry line-level

signals.

The rest of this section covers all BVT jacks and ways to connect

your equipment to them.

Bass Guitar

6.1 INPUT

High power

amplified signal

PURPOSE: To send an audio signal from an electric bass to the

Line level

signal

BVT.

RESULTS: The signal path begins at the INPUT jack.

6.2 TUNER

Line level

signal

PURPOSE: To send a copy of an audio signal from the BVT to

an electric tuner.

RESULTS: The main signal path is not affected.

If you use the:

= BVT4500H, you can reduce the volume of the PARALLEL

SPEAKER OUTPUTs or use the mute feature on your tuner.

For details, see TUNER jack (35).

= BVT5500H, you can mute the PARALLEL SPEAKER OUT-

PUTs and the LINE OUTPUT. For details, see MUTE button

{6}.

Fig. 5.1: BVT5500H setup example

In the above example,

6.3 LINE OUTPUT

The characteristic of the signal at the LINE OUTPUT jack depends

on the state of the PRE/POST switch.

= a speaker (ULTRABASS BA810),

= a mixer (XENYX 1832FX),

= and a tuner (RACKTUNER BTR2000)

are simultaneously connected to the BVT5500H.

6.3.1 PRE

However, you can tune without adjusting the speaker volume.

For details, see “FRONT PANEL” (MUTE button {8}) and “REAR

PANEL” (TUNER jack (35)).

PURPOSE: To send a copy of an audio signal to a mixer or a re-

cording unit without any preamp settings (TONE, EQ, EFFECTS).

See also section 6.3.2.

The audio signals that the ULTRABASS BA810 and the XENYX

1832FX receive from the BVT5500H are not the same:

RESULTS: The main signal path is not affected.

= The ULTRABASS BA810 receives a fully ampliﬁed signal.

6.3.2 POST

= The XENYX 1832FX receives a preampliﬁed (line-level)

PURPOSE: To process an audio signal with all BVT preamp

features (TONE, EQ, EFFECTS), and then send the preampliﬁed

signal to a mixer or, alternatively a recording unit.

signal.

You can select the type of preampliﬁed signal (PRE or POST

TONE/EQ/EFFECTS) that the BVT5500H sends. For details, see

“THE SIGNAL PATH”.

Notice that the LINE OUTPUT jack (with POST) derives the signal

before the MASTER control. This means the output level of this

jack is independent of the actual ampliﬁer volume.

Keep in mind that you can activate and deactivate the EQ sec-

tion. In addition, the BVT4500H and BVT5500H do not process

external effects in the same way. For details, see the section

“EFFECTS LOOP”.

RESULTS: The main signal path is not affected.

The signal path

ULTRABASS BVT4500H/BVT5500H

6.4 EFFECTS LOOP

The EFFECTS LOOP section can be used in three ways:

7. Audio connectors

This section illustrates the audio connectors that you need for

the BVT jacks. For details about most BVT jacks, see the section

“REAR PANEL”. For details about the INPUT jack, see the section

“FRONT PANEL”.

6.4.1 SEND and RETURN

PURPOSE: To create an effects loop, i.e., to apply external ef-

fects to the signal.

RESULTS: If you use the:

= BVT4500H, only the audio signal that enters via the RETURN

jack continues to follow the BVT4500H signal path. The level

of the effects has to be adjusted on the external unit.

= BVT5500H, both the main audio signal and the audio signal

that enters via the RETURN jack follow the BVT5500H sig-

nal path. To adjust the dry-wet mix, use the EFFECTS MIX

control.

6.4.2 SEND only (BVT5500H only)

PURPOSE: To send an audio signal from the BVT5500H to an

effects processor.

RESULTS: The main signal path is not affected.

Fig. 7.1: ¼" TS connector

6.4.3 RETURN only

PURPOSE: To send an audio signal from an external pre-amp

to the BVT4500H/5500H, i.e., to use the BVT as a power amp

only.

Speaker connector

(compatible with Neutrik Speakon connector)

RESULTS: If you use the:

= BVT4500H, the INPUT jack is deactivated. The signal path

begins at the RETURN jack.

= BVT5500H, the INPUT jack remains active. You could e.g.,

connect two basses to the BVT, one to INPUT and the other

to RETURN. To adjust the balance between the two, use the

EFFECTS MIX control.

6.5 INSERT CHANNEL

6.5.1 PREAMP OUTPUT

Fig. 7.2: The connector for a Neutrik Speakon compatible jack

PURPOSE: To process an audio signal with all BVT preamp

features (TONE, EQ, EFFECTS), and then send the audio signal

to an external power amp. The BVT settings affect the volume on

the external amp.

RESULTS: The main signal path is not affected.

6.5.2 POWER AMP IN

PURPOSE: To process an audio signal with an external preamp,

and then send the audio signal to the BVT4500H/5500H power

amp.

RESULTS: The signal path begins at the POWER AMP IN jack.

The signal is independent of the MASTER control.

Switch off the unit before connecting an external preamp

to POWER AMP IN.

Fig. 7.3: XLR connectors

Audio connectors

ULTRABASS BVT4500H/BVT5500H

8. System block diagram

Fig. 8.1: BVT4500/5500H block diagram (Rectangles represent control elements, ovals represent jacks.)

System block diagram

ULTRABASS BVT4500H/BVT5500H

Power supply

9. Speciﬁcations

BVT4500H

Power consumption

100 V~ 50/60 Hz: 6 A; 120 V~ 60 Hz:

5 A; 220 V~ 50/60 Hz: 3 A; 230 V~

50/60 Hz: 3 A

Audio Inputs

BVT4500H

Input

¼" mono jack, unbalanced (0 dB)

approx. 1 MΩ, unbalanced (pad 82 kΩ,

unbalanced)

Mains voltage / Fuse

100/120 V~ (50/60 Hz)

220/230 V~ (50/60 Hz)

Mains connector

Input impedance

T 10 A H 250 V

T 6.3 A H 250 V

Return

¼" mono jack, unbalanced

approx. 100 kΩ, unbalanced

¼" mono jack, unbalanced

approx. 100 kΩ, unbalanced

Standard IEC receptacle

Input impedance

Power amp input

Input impedance

BVT5500H

Power consumption

Mains voltage / Fuse

100/120 V~ (50/60 Hz)

220/230 V~ (50/60 Hz)

Mains connector

max. 550 W

BVT5500H

Input

T 8 A H 250 V

2 x ¼" mono jack, unbalanced (0 dB /

-15 dB)

approx. 1 MΩ, unbalanced / 82 kΩ,

T 4 A H 250 V

Standard IEC receptacle

Input impedance

unbalanced

Physical/weight

Return

¼" mono jack, unbalanced

approx. 100 kΩ, unbalanced

¼" mono jack, unbalanced

approx. 100 kΩ, unbalanced

BVT4500H

Dimensions (H x W x D)

Input impedance

Power amp input

Input impedance

approx. 26.8" x 16.1" x 13.7" (approx.

680 mm x 408 mm x 348 mm)

Weight

approx. 47.5 lbs (approx. 21.5 kg)

Audio Outputs

Loudspeaker connectors

BVT5500H

Dimensions (H x W x D)

2 x ¼" TS jack, 1 x professional

speaker connector (compatible with

Neutrik Speakon connectors)

approx. 26.8" x 16.1" x 13.7" (approx.

680 mm x 408 mm x 348 mm)

Weight

approx. 47.9 lbs (approx. 21.7 kg)

Load impedance

min. 4 Ω

BEHRINGER is constantly striving to maintain the highest professional standards.

As a result of these efforts, modiﬁcations may be made from time to time to existing

products without prior notice. Speciﬁcations and appearance may differ from those

listed or illustrated.

System data

BVT4500H

Output power

Peak power

Tone control range

Bass

450 W

±12 dB @ 50 Hz

±7 dB @ 700 Hz

±18 dB @ 5 kHz

MID

Treble

Graphic EQ range

33 Hz

±15 dB

±10 dB

±8 dB

±10 dB

±12 dB

80 Hz

150 Hz

300 Hz

600 Hz

900 Hz

2 kHz

5 kHz

8 kHz

BVT5500H

Output power

Peak power

Tone control range

Bass

550 W

±12 dB @ 50 Hz

MID

+7 dB @ 800 Hz / -7 dB @ 400 Hz

±18 dB @ 5 kHz

Treble

Graphic EQ range

33 Hz

±15 dB

±10 dB

±8 dB

±10 dB

±12 dB

80 Hz

150 Hz

300 Hz

600 Hz

900 Hz

2 kHz

5 kHz

8 kHz

Speciﬁcations

ULTRABASS BVT4500H/BVT5500H

10. Warranty

2. If the product needs to be modiﬁed or adapted in order to comply

with applicable technical or safety standards on a national or local

level, in any country which is not the country for which the product was

originally developed and manufactured, this modiﬁcation/adaptation

shall not be considered a defect in materials or workmanship. The

warranty does not cover any such modiﬁcation/adaptation, irrespec-

tive of whether it was carried out properly or not. Under the terms of

this warranty, BEHRINGER shall not be held responsible for any cost

resulting from such a modiﬁcation/adaptation.

§ 1 Other warranty rights and national law

1. This warranty does not exclude or limit the buyer’s statutory rights

provided by national law, in particular, any such rights against the seller

that arise from a legally effective purchase contract.

2. The warranty regulations mentioned herein are applicable unless

they constitute an infringement of national warranty law.

3. Free inspections and maintenance/repair work are expressly ex-

cluded from this warranty, in particular, if caused by improper handling

of the product by the user. This also applies to defects caused by nor-

mal wear and tear, in particular, of faders, crossfaders, potentiometers,

keys/buttons, tubes, guitar strings, illuminants and similar parts.

§ 2 Online registration

Please do remember to register your new BEHRINGER equipment right

after your purchase by visiting http://www.behringer.com and kindly

read the terms and conditions of our warranty carefully. Registering

your purchase and equipment with us helps us process your repair

4. Damage/defects caused by the following conditions are not covered

by this warranty:

claims quicker and more efﬁciently.

Thank you for your cooperation!

= improper handling, neglect or failure to operate the unit in

compliance with the instructions given in BEHRINGER user

or service manuals.

§ 3 Warranty

1. BEHRINGER (BEHRINGER International GmbH including all

BEHRINGER subsidiaries, except BEHRINGER Japan) warrants

the mechanical and electronic components of this product to be free

of defects in material and workmanship for a period of one (1) year*

from the original date of purchase, in accordance with the warranty

regulations described below. If the product shows any defects within

the speciﬁed warranty period that are not excluded from this warranty

as described under § 5, BEHRINGER shall, at its discretion, either

replace the product by providing a new or reconditioned product or

repair the product using suitable new or reconditioned parts. In the

case that other parts are used which constitute an improvement,

BEHRINGER may, at its discretion, charge the customer for the ad-

ditional cost of these parts. In case BEHRINGER decides to replace

the product, this warranty shall apply to the replacement product for

the remaining initial warranty period, i.e one year* from the date of

purchase of the initial product.

= connection or operation of the unit in any way that does not

comply with the technical or safety regulations applicable in

the country where the product is used.

= damage/defects caused by force majeure or any other condition

that is beyond the control of BEHRINGER.

5. Any repair or opening of the unit carried out by unauthorized per-

sonnel (user included) will void the warranty.

6. If an inspection of the product by BEHRINGER shows that the

defect in question is not covered by the warranty,

7. Products which do not meet the terms of this warranty will be re-

paired exclusively at the buyer’s expense. BEHRINGER will inform the

buyer of any such circumstance. If the buyer fails to submit a written

repair order within 6 weeks after notiﬁcation, BEHRINGER will return

the unit. Costs for freight and packing will be invoiced separately

C.O.D. When the buyer has sent in a written repair order such costs

will also be invoiced separately.

2. If the warranty claim proves to be justiﬁed, the product will be

returned to the user freight prepaid.

§ 6 Warranty transferability

3. Warranty claims other than those indicated above are expressly

excluded.

This warranty is extended exclusively to the original buyer (customer of

retail dealer) and is not transferable to anyone who may subsequently

purchase this product. No other person (retail dealer, etc.) shall be

entitled to give any warranty promise on behalf of BEHRINGER.

§ 4 Return authorization number

1. To obtain warranty service, the buyer (or his authorized dealer) must

call BEHRINGER during normal business hours BEFORE returning

the product. All inquiries must be accompanied by a description of

the problem. The buyer or his authorized dealer will receive a return

authorization number.

§ 7 Claim for damages

Failure of BEHRINGER to provide proper warranty service shall not

entitle the buyer to claim (consequential) damages. In no event shall

the liability of BEHRINGER exceed the invoiced value of the product.

* Customers in the European Union please contact BEHRINGER

Germany Support for further details.

2. Subsequently, the product must be returned in its original shipping

carton, together with the return authorization number. The return ship-

ment address will be indicated by BEHRINGER.

3. Shipments without freight prepaid will not be accepted.

§ 5 Warranty regulations

1. Warranty services will be furnished only if the product is accom-

panied by a copy of the original retail dealer’s invoice. Any product

deemed eligible for repair or replacement under the terms of this war-

ranty will be repaired or replaced.

Technical speciﬁcations and appearance are subject to change without notice. The information contained herein is correct at the time of printing. BEH-

RINGER accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or

statement contained herein. Colors and speciﬁcations may vary slightly from product. Our Products are sold through authorized dealers only. Distributors

and dealers are not agents of BEHRINGER and have absolutely no authority to bind BEHRINGER by any express or implied undertaking or representation.

This manual is copyrighted. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including

photocopying and recording of any kind, for any purpose, without the express written permission of BEHRINGER International GmbH.

+49 2154 9206 0, Fax +49 2154 9206 4903

Warranty

Acer Personal Computer VX4618GUI7260W User Manual
Acnodes Computer Monitor APH 8064 User Manual
ADI Systems Marine Radio AT 201 User Manual
Aiphone Marine RADAR LAF LDF User Manual
Aiwa MP3 Player CSD FD79 User Manual
Alpine Stereo Amplifier PDX 5M User Manual
American Standard Indoor Furnishings 0211008 User Manual
American Standard Indoor Furnishings T480500 User Manual
Aztech Systems Network Card WL635USB User Manual
Barco Projector 101 B User Manual